G4安装指南
G4安装指南
本教程适用于工厂生产的新板子，也适用于用 dd 命令破坏了分区结构的板子。
重要的事情说三遍：
- 不要 dd！！！
- 不要 dd！！！
- 不要 dd！！！
dd破坏板子分区之后的维修不属于 EE 工作范围，EE 不提供支持、答疑服务。
目录
安装 NL
步骤概览
- 下载 FL，烧写到 Type-C 口的 U 盘，让板子从 U 盘启动。
- 在 U 盘的 FL 中，为板子安装 NL。
- 拔掉 U 盘，重启板子到 1 分区，进入安装好的 NL。
- 基于 NL 可以继续安装 FL 或者 UP。
详细步骤（以 G4 为例）
1. 下载 FL 并烧写到 U 盘
FL 下载地址：
将 FL 烧写到 Type-C 口的 U 盘，让板子从 U 盘启动。
2. 下载 NL
NL 下载地址：
将 NL 的 cxp 文件 scp 到板子：
1 | |
注意： 文件名必须改为
NL.cxp。
3. 参考安装文档
在以下网页搜索文档号 131 63-KDU 137 0114/1 Uen：
下载文档 Program Storage Information for G4 products，参考 14.2.4 章节 Install NL。
4. 执行安装命令
确认板子有 /tmp/NL.cxp 之后，依次执行：
1 | |
注意： 不要忘记
vce write_unsecure命令，否则板子可能不会正常启动。
5. 完成
拔掉 U 盘，重启板子到 1 分区，即进入刚刚安装好的 NL。
安装 FL
Install FL using cxp image
- Download LXA cxp archive.
- Make sure the board enter NL on target.
- efibootmgr -n 1
- Restart by “pghli crestart” and wait for
[networkloader]#prompt - cp cxp-file into /tmp/. And rename it as FL.cxp
- Run “cup –nl-boot-install -p /tmp/FL.cxp”
- Set boot order list for G3.x “efibootmgr -o 2,1,0” or for G4 “efibootmgr -o 3,2,1,0”
- Restart by “pghli crestart” and wait for
[phv]#prompt or[factoryloader]#prompt for G4 target.
- Make sure the board enter NL on target.
安装 UP
Install UP/CXP’ using cup
This describes how to install CXPs/UP manually from NL in G4.
!!! OBS !!!
From RCSEE G4 R1A232 onwards corresponding NL R1A232 or newer is needed to be able to
install the node since there has been changes in LV volumes (rcs-lv has been replaced
by cscore-lv + mw-lv) and mount points of those, which requires that the NL version used to
perform the installation.
As long as a valid NL is included in the UP the AI will work from an old NL type 2, but if you
do manual installation using “cup” comamand you must make sure to first update NL type 3 to
the new version and start on that one.
1. Enter NL mode. To enter NL mode from phv or run mode in Linux, run command:
efibootmgr -n 1
pghli crestart
2. Run the command
cup --setup_fs
3. Fetch the CXPs or UP that you want to install from:
https://mia.npee.gic.ericsson.se/
4. If UP is used, transfer the UP to the node and unpack at e.g /tmp/
5. If CXPs, transfer the CXPs to node at e.g /tmp. NOTE: if needed start SSH on the board use:
/etc/init.d/sshd start
6. Create a list of the CXP’s to be installed including the path e.g:
ls -1 /tmp/*.cxp > /tmp/list
7. Run the command
cup -l -p /tmp/list
cup --confirm_os
8. Create needed links and pgh_no_restart flag (if wanted):
mkdir /tmp/home
cup --mkview home -e 1 -t /tmp/home
ln -s /software/* /tmp/home/sirpa/software/
mkdir /tmp/home/sirpa/ee
touch /tmp/home/sirpa/ee/pgh_no_restart
umount /tmp/home/
rmdir /tmp/home/
9. To start in phv mode:
pghli crestart -p
10. To start in run mode
pghli crestart
Now the system shall come up and mount all installed CXPs:
Note:
- If you restart and pgh_no_restart is added, next time you want to restart you need to use the -f force flag: pghli crestart -f
- Do not use the -f flag the first restart after step 8, that breaks the install
Optional
- In phv mode set the DebugSwitch board variable to 3 with “testbox board_var write DebugSwitch 3” to always boot in to phv mode.
- Install overlayfs using “install_overlayfs” and reboot.
To build an own CXC/CXP:
cd rcs-yocto
make -C make/g4-hw package
<path to rcs-test>/jenkins/makecxp -r <CXC rev> -R <CXP rev> -o make/build/build_intel-axxia-grr_g4-hw/export/delivery/RCSEE-G4_CXP2030215_1.cxp -i make/build/build_intel-axxia-grr_g4-hw/export/delivery/
Latest RCSEE-G4 CXP:
locally
/proj/ee-tmp/rcs-ee-yocto/g4-ee/rcs-yocto-g4-master-latest/black_cxps/RCSEE-G4_CXP2030215_1-R99*.cxp
or MIA/Nexus:
https://mia.npee.gic.ericsson.se/products/CXP2030215_1
Prebuilt UP
/proj/ee-tmp/rcs-ee-yocto/g4-ee/rcs-yocto-g4-master-latest/dus_G4-up/
Build a UP:
<path to rcs-test>/ee-install/mkrcseecxs.sh -v -o EE_BLACK_DUS_G4_MINI.zip -V g4_master-1 -i make/build/build_intel-axxia-grr_g4-hw/export/delivery/RCSEE-G4_CXC2014049_1.tar.gz -u /proj/rcsee/yocto/g4/bufferBaseline/EE_BLACK_DUS_G4_MINI.zip -n main